How to connect a carpet to each other

In the case of repair and replacement of the flooring in the house, you need to think through all the nuances and choose a really good option. If you decide to purchase a carpet, you need to know how to properly lay it and connect it to create an even floor.

In order for the carpet to last longer and not cause inconvenience, it is very important to correctly fulfill all conditions. However, few people know how to connect the coating without visible seams. In the article we will try to analyze the most popular ways and help create the perfect floor in your home or apartment.

First you need to decide on the necessary tools. For work, we need:

1. Electric jigsaw.
2. Hammer drill.
3. Shoe knife or sharper clerical with interchangeable blades.
4. Hacksaw for metal.
5. A set of measuring tools.
6. Pencil or marker for marks.
7. Screwdrivers for plus (Phillips).
8. The rule.

This kit is relevant for any of the possible methods for joining carpet, described below. If necessary, you can use for convenience additional improvised tools of your choice.

IMPORTANT! Carry out the work carefully so as not to damage the material. Better to take it with a margin.

After preparing everything you need, select one of the proposed options. There are several ways to do this, some of which are presented below:

1. The overlap joint. A fairly simple way to execute.
2. Use in the construction of a special strap. This method will be relevant for interior transitions, since the junction will slightly protrude.
3. Work with a special iron to connect the edges of the coating.

Even if you were able to accurately calculate the required footage of the carpet for each room, it is still recommended to establish connections. This will ensure a high-quality coating and extend the service life, since without joining the material can bend and eventually deteriorate from frequent mechanical damage.

How to join a joint overlap carpet

The first method involves the creation of a special overlay of material on each other, so you should purchase it with a margin.

1. Lay the edges of the carpet on top of each other, forming an overlap of about 8-10 cm.
2. Place a strip of cardboard under it.
3. Using a knife, make a longitudinal cut (tilt angle of approximately 40 °).
4. Glue the coating with special adhesive tape on both sides.

ATTENTION! If there is a pattern on the carpet, try to fit it so that it is preserved after cutting. This method is best used in places that usually do not attract attention (behind a cupboard, sofa, in the corner of the room).

How to connect parts of the cover strips

The following method is suitable for connecting the coating in doorways. It will create a path and divide the space perfectly:

1. Measure the length of the bar.
2. Cut the part to the required length.
3. Make both joined edges even.
4. Press the material firmly against the floor and lay the bar over it.
5. Make holes in the floor for future fixing.
6. Fasten the bar with fasteners.

IMPORTANT! Of all the models, it is more convenient to use the bar with the smallest protrusion for convenient location. Too large elevations will interfere.

How to glue carpet parts

The use of glue should be resorted to after careful consideration and evaluation of the main coating. In case of replacement or complete removal of the coating, the adhesive may leave marks and deform the surface of the floor. If you decide to use this particular option, follow the instructions.

First, apply glue to the main coating and to the edges of the carpet about 5 cm in both directions. Then firmly press the material and fix it until it dries completely. At the same time, with a dry cloth, remove excess glue that will appear in between. If necessary, the adhesive base can be periodically updated to improve fixation.

Using a special iron

One of the better ways of fastening is iron. It allows the product to fit tightly without gaps:

1. Trim the edges of the carpet in the manner described above.
2. Apply a special bonding agent.
3. Apply a tape 7 cm wide at the junction.
4. Apply the coating and let it dry. Drying is done with hot air from the iron.
5. Comb the pile to remove the visible part of the cut, ensuring a tight connection.

IMPORTANT! Do not wait until the base has dried, all actions should be performed quickly before the composition hardens.

If you doubt the choice of joining method, you should pay attention to the following factors that play an important role in joining the coating:

• choice of docking place;
• flatness of the floor and the presence of protrusions or small roughnesses;
• floor strength and susceptibility to deformation;
• quality of the main material of which the carpet is made;
• method cost;
• the availability of time, the ability to use complex methods.

Analyze all the items and choose the most suitable for your apartment. The coating should look nice and create a visual effect of integrity.